Important Plumbing Guide for Installing a Bathtub
Important Plumbing Guide for Installing a Bathtub
Blog Article
How do you actually feel when it comes to Installing A Bathtub?
Installing a bathtub isn't exactly rocket science, however it does need strong plumbing, carpentry, as well as in some cases, tiling abilities. Replacing an old bath tub with a new one is also a reasonably difficult task. If the old bathtub is conveniently obtainable, the job can move immediately; if you have to open up a wall to remove the old bathtub as well as position the brand-new tub, the job is a lot harder. In either case, the task is within a residence handyman's abilities, although you will need a helper to move out the old bathtub and embeded in the new one. See to it you have actually qualified on your own for the job and also are comfortable attempting it. Rather than working with a service provider to take over a halfway-completed task, it is better to take into consideration utilizing one prior to you begin. Possibilities are you might require an expert plumber to make tube links.
This article will certainly aid you install a brand-new bath tub in your restroom if you have already acquired a new tub as well as do not require to change the arrangement of your previous supply of water pipes.
Your devices and also product checklist should consist of the following:
Planning for the Installment
To start with, the sustaining structure provided with the bathroom ought to be fitted (if required) according to the supplier's instructions. Next off, fit the faucets or mixer to the bath tub. When suitable the tap block, it is very important to make certain that if the faucet features a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bath, it is likewise practical to fit a sustaining plate under the taps system to avoid pressure on the tub.
Fit the adaptable faucet ports to the bottom of both taps making use of 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet through the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. See to it you make use of every one of the supplied washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath should now prepare to be suited its final setting.
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your setup, then the first thing you ought to do is detach the water system. After doing so, switch on the taps to drain pipes any type of water staying in the system. The process of getting rid of the existing taps can be quite bothersome due to the limited gain access to that is typically the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the faucets. Have a fabric all set for the staying water that will certainly come from the pipelines. Once the supply pipelines have actually been removed, use the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary faucets from transforming during this process. Once the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any type of old sealing compound.
Before moving on to fit the new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new taps to fit.
Installing the Bath tub
Utilizing the two wood boards under its feet, place the bath tub in the required placement. The wooden boards are useful in equally spreading the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four tiny points.
The next goal is to make certain that the bathtub is leveled all round. This can be attained by checking the spirit level as well as readjusting the feet on the bathtub until the spirit level reads level.
To set up taps, fit all-time low of the outermost adaptable tap connector to the ideal supply pipeline by making a compression sign up with; after that do the exact same for the other tap.
Turn on the water and also examine all joints and also new pipework for leaks and tighten them if necessary. Fill the bath tub and also examine the overflow outlet and the regular outlet for leaks.
Finally, take care of the bath paneling as explained in the producer's instruction manual. Tiling and also sealing around the bath tub should wait till the bathtub has been made use of a minimum of when as this will resolve it into its last setting.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will require a plastic port to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet as well as the other end gives a connection to the current supply pipes.
If you require to fit a monobloc, after that you will certainly require lowering couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, position the tap in the placing hole in the bath/basin making certain that the washers are in location between the faucet and the sink. Secure the faucet in position with the maker supplied backnut. When the tap is safely in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical faucet ports. The previous kind must be attached to the tap finishes first, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bathroom fulfills the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is necessary as the installation can move enough to crack an inflexible seal, creating the water to permeate the wall surface between the bathroom and the tiling, leading to complications with moisture and also feasible leaks to the ceiling listed below.
You can choose from a variety of coloured sealants to blend in your components and also fittings. They are marketed in tubes as well as cartridges, as well as are capable of securing gaps up to a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill the tub with water prior to securing, to allow for the movement experienced when the tub is in use. The sealant can split relatively very early if you do not take into account this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily readily available on the market. It is suggested to fit the tiles utilizing water-resistant or waterproof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been shown that write-up about A Step-by-Step Guide to Installing a Bathtub through an associate on another web property. Enjoyed reading our review? Please share it. Let other people locate it. Kudos for your time. Kindly come visit our blog back soon.
Ensure plumbing integrity; reach out. Report this page